top of page
belt applicator 4.jpg
flexwipe1wide copy.jpg

FlexWipe Applicator

Enhancing safety - The unique Tactile arm eliminates any risk of crushing between the moving applicator arm and the printer or the pallet. If you put your hand in the way, the stepper motor driven arm stops and the system gives an alarm. The Tactile arm together with the Pivotable machine mount, negates the need of expensive guarding. This does not only reduce cost and release floor space, it also gives direct and quick access to the system for the operator. The label roll is replaced within 20 seconds and it takes only a minute to replace the print head or print roller when needed.

Evolabel FlexWipe pallet labeling system turns traditional pallet labelling up-side-down.


Instead of being dangerous, hard to use, large, slow and expensive, the Evolabel FlexWipe system is totally safe, user friendly, compact, fast and cost effective.

Safe, compact, fast and cost effective. Evolabel FlexWipe is a giant leap for Pallet Labeling!

Front, Side and Rear pallet labeling


The free motion apply (patent pending) allows the same configuration to apply either of the two adjacent sides (side+front or side+back) within 12 seconds. This includes validation of all barcodes on the GS1 SSCC label. The FlexWipe system can label all three sides without having the pallet to stop if check scanning is not required.

Essity Hygiene and Health


At Essity Hygiene and Health in Lilla Edet, Sweden, the Evolabel FlexWipe system prints and applies 5 pallets per minute, on two sides including verification of all barcodes. More important still, is the fact that the system is totally safe. Both the risk of pinching between the applicator arm and the printer and the risk of getting stuck between the pallet and the whole system are eliminated with intelligent solutions.


FlexWipe Applicator Technical Specifications

Evolabel FlexWipe pallet applicator is a safe, compact, fast and easy to use solution for tough industrial environments.

The FlexWipe is releasing flexibility due to both the compact nature of the unit and the same applicator can label all three sides towards the system.

It is built upon two servo controlled rotating movements. The inner monocoque arm can rotate 360º and the labels can leave the printer in two directions (patent pending). The outer arm holding the applicator pad can rotate 200º.

A camera based scanner is located behind the applicator pad. When a validation check scan is required the arms move and turn 180º to an optimal reading position, where all printed barcodes are checked.

  • Suitable printer models: T63 G2

  • Minimum Label size (WxL): 80x80 mm 

  • Maximum Label size (WxL): 178x240 mm

  • Label height position (top of label): Standard 770 +/- 400 mm                        (Optional 1270 +/- 400 mm)

  • Label position (symmetric) at min distance (50 mm) between applicator and pallet:  237 mm from pallet corner to near edge of A5 label

  • Minimum separation between pallets: 750 mm

  • Weight ( applicator): 20 lbs. (9kg)

  • Weight (T63 printer+applicator): 84 lbs. (38kg)

  • Weight (FlexWipe,T63 + stand): 181 lbs. (82 kg)

  • Models: One model for any side

  • Label position (assymetric) at smallest possible separation between pallets (450 mm):                                                                       Front/Back label: 50 mm from pallet corner to near edge of  A5 label  Side label: 343 mm from pallet corner to near edge of A5 label

  • Distance between applicator and pallet: 215 mm

  • Air supply: 6 bar, clean and dry

  • Capacity (2-side labeling): Exceeds 5 pallets/min

  • Dimensions (WxDxH): 916x610x2047 mm

  • Operating temperature: +5°C to +40°C (down to -28°C provided that the power is always switched on)

  • Humidity: 20 to 85%, non-condensing

Evolabel FlexWipe Applicator Video

Related Products
T43 with hand.jpg
T63 printer.jpg
bottom of page